Industry edition · Content and Video
Bend values for the publisher's own equipment appear in three of 10 sheet metal design guides
We looked at 10 sheet metal design guides and could open nine. Each guide we opened covers at least seven of the nine design topics we checked for, and three list bend radius and other values that the publishing company says apply to its own equipment.

According to estimates we pulled from Ahrefs’ Keywords Explorer on Nov. 6, 2026, US searchers type “sheet metal design guide” into Google 150 times a month, and “k factor sheet metal” and “sheet metal bend radius” get 150 searches a month each. We looked at 10 guides an engineer can find for those questions. Nine can be read on the page without a form, and all nine explain bend radius, hole placement near bends and edges, tolerances and material choice, mostly as rules of thumb written in multiples of sheet thickness. Three of the 10 publish values that their companies say apply to their own equipment: Approved Sheet Metal, SendCutSend and Protolabs.
If you run marketing at a fabricator, the general rules are already published many times over. We think your guide should publish your shop’s own numbers: inside bend radius, K-factor and minimum flange by material and gauge for the tooling on your press brakes, your standard tolerances, the hardware you insert and the finishes you offer. Put the guide on an HTML page, with a link to send a drawing for review.
What do engineers search for when they design a bent part?
Ahrefs puts “sheet metal design” at 500 US searches a month, with “sheet metal design guide” as its parent topic. The specific questions are smaller: “sheet metal bend radius chart” draws 100 a month, “sheet metal design guidelines” 100, “minimum flange length sheet metal” 50 and “hole to edge distance sheet metal” 20. These are design searches, and the local searches buyers use to find a shop are a different set, covered in our piece on machine shop search. Ahrefs scores keyword difficulty (KD) from 0 to 100; “sheet metal design guide” scores 13 and the four specific questions 0 to 5. Ahrefs also estimates a cost per click of $7.00 for “minimum flange length sheet metal” and $9.00 for the buying search “sheet metal fabrication quote”.
What do published sheet metal design guides cover?
Seven guides came from two web searches our researcher ran on Nov. 6, 2026 for sheet metal design guidelines, and the other three came from the publishers’ own sites. We added Approved Sheet Metal’s reference guide because the shop’s design resources hub and its eBook landing page both link to it, and we found Protolabs’ and Xometry’s guides by browsing their sites. Five of the 10 publishers are US companies: Approved Sheet Metal (a job shop), Fabcon (a contract fabricator), SendCutSend (an online fabricator), Protolabs (a digital manufacturer) and Xometry (a marketplace). Geomiq is a UK platform, and JLCCNC, RapidDirect, PCBWay and Yijin Solution are based in China.
We read each page and coded nine technical topics. A topic counts when the page itself gives a rule, a value or an explanation for it; a mention in a menu or a link title does not count. Word counts cover the article text with menus, footers, related-post lists and author bios removed.
The nine readable guides run from 1,876 words (RapidDirect’s 20-page PDF) to 4,368 words (Geomiq). Fabcon and Yijin Solution cover all 9 topics, five guides cover 8, and Approved Sheet Metal and JLCCNC cover 7. Finishing is the topic most often left out, covered by 5 of the 9. Xometry’s guide is an eBook behind a form that asks for name, work email, phone number and company, and its landing page gives a contents list of 306 words with no rules or values, so we coded it as gated.
| Guide (publisher type) | Bend radius | K-factor | Hole to edge or bend | Min. flange | Bend relief | Tolerances | Material or gauge | Hardware | Finishing | Topics of 9 | Words | Own values |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Fabcon (US contract fabricator) | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | 9 | 3,579 | No |
| Yijin Solution (China fabricator) | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | 9 | 2,881 | No |
| SendCutSend (US online fabricator) | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | No | 8 | 2,142 | Yes |
| Protolabs (US digital manufacturer) | Yes | No | Yes | Yes | Yes | Yes | Yes | Yes | Yes | 8 | 2,353 | Yes |
| Geomiq (UK platform) | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | No | 8 | 4,368 | No |
| RapidDirect PDF (China platform) | Yes | Yes | Yes | Yes | No | Yes | Yes | Yes | Yes | 8 | 1,876 | No |
| PCBWay (China online fabricator) | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes | No | 8 | 2,184 | No |
| Approved Sheet Metal (US job shop) | Yes | Yes | Yes | No | No | Yes | Yes | Yes | Yes | 7 | 2,496 | Yes |
| JLCCNC (China online fabricator) | Yes | Yes | Yes | Yes | Yes | Yes | Yes | No | No | 7 | 3,553 | No |
| Xometry (US marketplace) | Gated | Gated | Gated | Gated | Gated | Gated | Gated | Gated | Gated | 0 on page | 306 | No |
| Readable guides covering the topic (of 9) | 9 | 8 | 9 | 8 | 7 | 9 | 9 | 8 | 5 | 3 |
All nine readable guides cover at least 7 of the 9 topics, and three publish values tied to the publisher's own equipment. Read Nov. 6, 2026. A topic counts when the page gives a rule, value or explanation for it. Words are our count of the article text without menus, footers or related posts. Xometry's guide is a download behind a lead form, so its page is coded as gated. Source: Plant to Pipeline review of 10 sheet metal design guides, Nov. 6, 2026.
Where do the rules of thumb in these guides disagree?
Most guides write their rules as multiples of sheet thickness (t) and the inside bend radius (R), and the published values differ on two rules an engineer uses at the CAD stage. Apart from Fabcon, the guides in Fig. 02 put minimum flange length between 2.5t and 4t, and four of the six use 4t. Hole-to-bend distances in those six guides run from 2t at JLCCNC and PCBWay to 4t at RapidDirect, with Yijin Solution giving a range of 3t to 4t. Protolabs says features within 4t of a bend are at risk of deforming. Fabcon gives two values for each rule on the same page. In one passage its minimum flange is R + 3t or 0.7 times the V-die opening, whichever is larger, and in another it is about 4t to 6t from the bend tangent. Its hole-to-bend clearance is 2.5t + R in one place and R + 2t, measured from the bend tangent line, in another.
Several guides say the numbers are starting points. Fabcon’s guide says each value “must be confirmed with the fabricator”. Yijin Solution’s table and PCBWay hedge the hole-to-bend rule in particular, with Yijin Solution adding “confirm with fabricator” to it and PCBWay giving its 2t distance “as a starting point”.
| Guide | Minimum flange length | Hole to bend distance |
|---|---|---|
| Geomiq | 4t | 2.5t + R |
| Yijin Solution | 4t | 3t to 4t |
| RapidDirect | 4t | 4t (features from any bend line) |
| Protolabs | 4t | 4t (features within 4t of a bend risk deforming) |
| JLCCNC | 3t | 2t (to the bend tangent line) |
| PCBWay | 2.5t to 4t | 2t (as a starting point) |
| Fabcon | R + 3t, or 0.7 x V-die opening if larger; about 4t to 6t from the bend tangent elsewhere on the page | 2.5t + R; R + 2t from the bend tangent line elsewhere on the page |
The seven guides set minimum flanges from 2.5t to 6t and hole-to-bend distances from 2t to 4t, with some formulas adding R, and Fabcon gives two values for each rule. t is sheet thickness and R is inside bend radius. SendCutSend publishes its own minimum flange for each material and thickness instead (0.309 in. for 0.059 in. mild steel). Approved Sheet Metal gives no minimum flange rule. Its section on features near bends says to place holes and slots at least 4t "from the outside edge". Read Nov. 6, 2026. Source: Plant to Pipeline review of sheet metal design guides, Nov. 6, 2026.
What do the guides with their own numbers publish?
Approved Sheet Metal, a job shop in Hudson, N.H., recommends an inside bend radius of 0.030 in. for most parts up to 0.125 in. thick, says it holds plus or minus 1 degree on most bend angles and recommends a K-factor of 0.3 to 0.5. It also says “only about 15% of sheet metal prototypes we see at ASM require a bend radius equal to the material thickness.” Of the eight rows in its tolerance table, the tightest are plus or minus 0.005 in., for a sheared edge to a hole and for two holes on one surface, and the loosest are plus or minus 0.030 in., for holes across two or four bends and for the formed part. The guide’s hole-to-edge, notch, tab and offset values match the figures on Protolabs’ guidelines page, and most of the guide’s tolerance rows carry the values Protolabs gives for comparable features in material under 0.13 in. Approved Sheet Metal’s K-factor range, 15% figure and recommendation of 0.030 in. for most parts up to 0.125 in. thick do not appear on Protolabs’ page, which lists 0.030 in. as one of four standard bend radii.
SendCutSend’s bending page says bend radius and K-factor “are set per material thickness” and sends the engineer to its Bending Calculator, which holds one HTML table of 59 material and thickness rows across 10 materials. Each row gives the K-factor, bend deduction, effective bend radius, die width, minimum flange and relief dimensions. For 0.059 in. mild steel, the table lists a K-factor of 0.40, an effective radius of 0.063 in. and a minimum flange of 0.309 in. The page also offers gauge tables to import into Autodesk Fusion or SolidWorks, and a table of die widths with the minimum distance from a bend line to a cutout for each.
Protolabs’ design guidelines list four standard bend radii (0.030, 0.060, 0.090 and 0.120 in.) available “in a 3 day lead time”, tolerance tables for material under and over 0.13 in. thick, and a table of the thicknesses Protolabs stocks in 11 grades of steel, stainless steel, aluminum, copper and brass.
Should a sheet metal design guide sit behind a form?
Two publishers in the set put some of their design guide content behind a form. Xometry’s guide is a download that needs a name, work email, phone number and company before it opens. Approved Sheet Metal’s reference guide says the shop built its bend gains chart “from our actual tooling and process data”. The chart and the shop’s design eBook sit behind a form asking for email, name, company and state, while the shop’s default tolerance sheet and hardware reference sheet open as PDFs with no form.
Our view is that the numbers an engineer needs while modeling belong on an open HTML page, because the engineer is usually in CAD with a part to finish, and a search engine or AI assistant can read and cite a page but cannot fill in a form. A shop can still put a fuller chart or an eBook behind a form, as Approved Sheet Metal does with its bend gains chart and design eBook while keeping key values open in its reference guide.
What should a fabricator publish from its own tooling?
We recommend five steps, which produce a guide page built on your own tooling.
- Ask your press brake lead for the punch and die combinations you run on standard work, and build a table with one row per material and gauge: thickness, inside bend radius, K-factor or bend deduction, die width and minimum flange. Take the values from your own tooling and process data, as Approved Sheet Metal says it does for its bend gains chart, or from a test bend on production material, the bend coupon Fabcon’s guide describes. Put the date the table was last checked at the top.
- Publish your standard tolerances as a table by feature (edge to hole, across one bend, across two bends), using the values your quality manager will accept on a first article.
- List the inserted hardware you stock (self-clinching nuts, studs and standoffs) with the minimum sheet thickness and hole size you use for each, and the finishes you apply in house or through a vendor, with your rule on whether hardware goes in before or after coating.
- Put all of it in HTML on one page titled with the phrase people search for, such as “Sheet metal design guide: bend radius, K-factor and minimum flange”, and offer the bend table from step 1 as a PDF and as a gauge table for SolidWorks or Fusion, with no form.
- End the page with a link to upload a drawing for design for manufacturability (DFM) review, and track how many drawings arrive through it.
The same tables can go on a capabilities page, as our piece on capability statements describes, and into application stories. Our review of eight application stories found that only one, Cincinnati Incorporated’s story on Vicon Fabricating, stated its constraints with values.
Sources
- Ahrefs Keywords Explorer, overview, US, pulled Nov. 6, 2026 (sheet metal design terms: volume, KD, CPC, parent topic)
- Approved Sheet Metal, DFM & Design Reference Guide
- Approved Sheet Metal, sheet metal design resources
- Approved Sheet Metal, sheet metal design for manufacturing eBook
- Approved Sheet Metal, sheet metal bend gains chart
- Approved Sheet Metal, Recommended Default Sheet Metal Tolerances (PDF)
- Approved Sheet Metal, hardware reference sheet (PDF)
- Approved Sheet Metal, About
- Fabcon, sheet metal design best practices
- SendCutSend, CNC bending services and guidelines
- SendCutSend, Bending Calculator
- Protolabs, sheet metal fabrication design guidelines
- Xometry, design guide: sheet metal fabrication
- Geomiq, sheet metal design guide
- JLCCNC, sheet metal design
- RapidDirect, sheet metal fabrication design guide (PDF)
- PCBWay, sheet metal bending design guidelines
- Yijin Solution, sheet metal design guidelines
- Plant to Pipeline, what buyers search when they look for a machine shop
- Plant to Pipeline, capability statements for job shops
- Plant to Pipeline, manufacturing application stories
See an error? Email editor@planttopipeline.com with what is wrong. We fix errors and log them on the corrections page.
Filed under
Filed under


